Fluke 789 / 787 ProcessMeter

fluke 787 processmeter 1.jpg (34632 bytes)

Double Your Power

A maintenance and calibration tool that will be at home in every instrumentation technician's tool box, the Fluke 787 ProcessMeter combines a DMM and a Loop Calibrator in one rugged, handheld tool, for about what you would expect to pay for a loop calibrator alone. Based on the trusted Fluke 87 DMM, the 787 adds the ability to measure, source, and simulate dc loop current with 0.05% accuracy and 1 microamp resolution. The 787 offers:

Simultaneous mA and % of scale readout on mA output.
25% Manual Step plus Auto Step and Auto Ramp on mA output.
Clear LCD with backlight; 4,000 counts (30,000 counts for dc current)
Min/Max/Average/Hold/Relative modes.
Externally accessible battery for easy battery changes.
1000V overload protection on V, ohms, frequency.
150V overload protection on mA, backed up by 440 mA 1000V fuse.

The Fluke 787 was the first tool to combine a DMM and a loop calibrator to give process technicians double the power in one tool. Now it’s even better, the range is extended with the new Fluke 789 – the ultimate loop calibration multimeter. The Fluke 789 has a 24-Volt loop supply reducing the need for taking a separate power supply when doing offline transmitter testing. And with its built-in, selectable 250-Ohm Hart® resistor, it also eliminates the need to carry a separate resistor with you. Now process technicians can do a lot more while carrying a lot less.

Fluke combined the DMM you trust with the loop calibrator you need.

The Fluke 787 ProcessMeterT puts a complete troubleshooting solution in the palm of your hand. Get in touch with more information, faster and easier with the newest member of the Fluke 80 Series, the 787 ProcessMeter. The 787 gives you the measurement capabilities you expect from our rugged, reliable DMMs plus the ability to source, simulate, or measure dc current with 1 microamp resolution and accuracy of 0.05%. Put it all together and you have the ideal tool for troubleshooting and calibrating current loop applications. So if you're tired of always tracking down a calibrator, lugging around two tools and switching back and forth, get the single best solution for doubling your power. The 787 ProcessMeter from Fluke.

Now it’s even better, the range is extended with the new Fluke 789 – the ultimate loop calibration multimeter. The Fluke 789 has a 24-Volt loop supply reducing the need for taking a separate power supply when doing offline transmitter testing. And with its built-in, selectable 250-Ohm Hart® resistor, it also eliminates the need to carry a separate resistor with you. Now process technicians can do a lot more while carrying a lot less.

fluke 787 processmeter 2.jpg (20268 bytes)

DMM and loop calibrator in one tool
Precision 1000V, 440 mA digital multimeter
- Measure ac and dc volts, ac and dc current, resistance, continuity, and frequency
- 0.1% dc voltage accuracy
- 0.05% dc current accuracy, 1 ‘A resolution to 30 mA
- Simultaneous mA and % of scale readout
- True rms ac voltage measurement to 1 kHz
- Frequency measurement to 20 kHz
- Min/Max/Average/TouchHold/Relative modes
- Diode test and continuity beeper
DC current source/loop calibrator
- 20 mA current source/simulator
- Simultaneous mA and % of scale readout
- Manual step (25%, coarse, fine) plus auto step and auto ramp
Clear LCD with backlight; 4,000 counts (30,000 counts for dc current)
Externally accessible battery for easy battery changes
1000V overload protection on V, ohms, frequency
150V overload protection on mA, backed-up by 440 mA 1000V fuse
Designed to meet 1000 volt IEC 1010 Cat III standards

Fluke 789	ProcessMeter™ w/holster	$795.00*
Fluke 787	ProcessMeter™ w/holster	$649.00*

Includes.....	C81Y yellow protective holster and flex stand
	Instruction manual / operators guide
	TL75 Test leads
	AC70A Alligator clips
	9V Battery

Fluke 787 / 789 ProcessMeter™