True-rms current (ac + dc)
Ranges: 50.00 A, 500.0 A, 5.000 kA, 50.00 kA,
1250 KA
Accuracy: ±(1% +10 counts)
 

Frequency
Ranges: 10.0 Hz to 15.0 KHz
Accuracy: ±(0.5% + 2 counts)
 

PF Power Factor
Ranges: 0.00 to 1.00
Accuracy: ± 0.04
 

DPF Displacement Power Factor
Range: 0.00 to 0.25 Not specified,
0.25 to 0.90 ± 0.04, 0.90 to 1.00 ± 0.03
 

Phase: Volt & Amps (between Fund & Harmonic) Accuracy: 2nd (± 3º) . . . 51st (± 15º)
Watts (between Volt Fund. & Amps Harmonic)
Accuracy: Fund (± 15º)
 

K-Factor (Amps & Watts):
Range: 1.0 to 30.0
Accuracy: ± 10%
 

Vrms actual, Vrms max, min (AC+DC):
5.000 V, 50.00 V, 500.0 V, 1250 V^*
Accuracy: Readings ±(2% + 10 counts), Cursor readings ± (2% + 12 counts), Cursor Readings Average ± (2% + 10 counts)
 

Parameters: Choose up to two from one of the groups below:
 

V/A/Hz: Line voltage, current, frequency
 

Power: Watts, VA, VAR, PF, DPF, frequency
 

Harmonics: THD, volts(Fund. & Harmonics), Amps (F&H) Watts (F&H) Freq. (H),%(H) of total, Phase(H), KF
 

Ohms: Ohms, Diode, Continuity, Capacitance
 

Temperature: °C or °F
 

Useful bandwidth input 1: DC to 1 MHz (with test leads TL24)

Number of transients 40
 

Voltage threshold settings: 20%, 50%, 100%, 200% above or below reference signal
 

Reference signal: After START, the Vrms and frequency of the signal are measured. From these data a pure sinewave is calculated as reference for threshold setting.
 

Inrush times (selectable):
1 s, 5 s, 10 s, 50 s, 100 s, 5 min
 

Cursor readings
A Peak max at cursor 1 and cursor 2
Accuracy: ± 5% of full scale

Input 1:
Ranges: 1 MW//12 pF; with BB 120: 20pF
Accuracy: ±2 pF; with BB120 ±3 pF
 

Input 2:
Ranges: 1 MW//10 pF; with BB 120: 18pF
Accuracy: ±2 pF; with BB120 ±3 pF
 

Vertical
 

Voltage Ranges:
Ranges: 50 mV/div to 500 V/div
Accuracy: ± (1% + 2 pixels)
 

Vertical sensitivity, resolution:
Ranges: 5 mV/div to 500 V/div, 8 bit (256 levels)
 

Bandwidth input 1 (voltage):
Ranges: DC to 20 MHz at inputs, or with BB120 and VPS 100-R probe (opt); 1 MHz with TL24 Leads
 

Bandwidth input 2 (current):
DC to 15 kHz at inputs
10 kHz with 80i-500s Current Clamp
 

Coupling:
DC, AC (10 Hz -3 dB)
 

Horizontal
 

TimeBase modes:
Normal, roll, single
 

TimeBase ranges:
Ranges: 60 s/div to 20 ns/div
Accuracy: ± (0.4% + 1 pixel)
 

Sampling rate: 25 MS/s
 

Record length (min/max samples):
512 per channel
 

Trigger source:
Ranges: Input 1 or Input 2 or Automatic selection
 

Trigger Mode:
Automatic Connect-and View^TM, Free Run, Single Shot.
 

Connect-and-View^TM:
Advanced automatic triggering that recognizes signal patterns and automaticaly adjusts triggering, timebase and amplitude. Automatically displays stable pictures of complex and dynamic signals like motor drive and control signals.
 

Pre Trigger:
Up to 10 divisions
 

Diode voltage:
Ranges: 0 to 3.000 V
Accuracy: ±(2% + 5 counts)
 

Continuity, shorts > 1 ms:
Ranges: Beeper on at < (30 W ± 5 W)
Accuracy: Not Applicable
 

Capacitance:
Ranges: 50.00 nF, 500.0 nF, 5.000 µF, 50.00 µF,
500.0 µF
Accuracy: ±(2% + 10 counts)
 

Temperature:^{* *}
Ranges: -100.0 ºC to 400.0 ºC, (-200.0 ºF to 800.0 ºF)
Accuracy: ±(0.5% + 5 counts)